联系我们
名称：彩色透水地坪品牌厂
电话：xxx
手机：xxx
邮箱：xxx
地址：xxx
新闻动态
防静电地坪漆是由高级环氧树脂
防静电地坪漆是由高级环氧树脂、高效导电材料，高级颜料助剂，按一定比例配比环氧专用固化剂的双组分涂料。环氧防静电地坪漆抗静电效果优良持久，防潮，耐磨，不受时间、温度、湿度等影响防尘。面光洁平整，能消除及防止静电和电磁波产生，避免静电火花及电磁波乾扰及破坏。
The anti-static floor paint is a two-component paint composed of high-grade epoxy resin, high-efficient conductive materials, high-grade pigment additives and a certain proportion of special curing agent for epoxy. The anti-static effect of epoxy anti-static floor paint is excellent and durable, moisture-proof, wear-resistant, and not affected by time, temperature, humidity, etc. The surface is smooth and smooth, which can eliminate and prevent the generation of static electricity and electromagnetic wave, and avoid the interference and damage of static sparks and electromagnetic wave.
防静电地板漆，漆膜表面电阻为106-109欧姆，优先防止静电荷泄露，消除静电积累和电磁乾扰的危害。环氧防静电地坪拥有环氧树脂地坪的一切优异性能，表面电阻率达到106Ω-109Ω、地面电阻排泄符郃国际GB6650-86A标准。该地板整体无缝，能达到:防尘、坚韧耐磨、耐冲击、耐重压、耐腐蚀、耐溶剂、平整亮丽、著色自由、便於清理、维护，保养，且使用寿命长之目的。
The surface resistance of anti-static floor paint is 106-109 ohm. The priority is to prevent the leakage of static charge and eliminate the hazards of static accumulation and electromagnetic interference. The epoxy anti-static floor has all the excellent properties of epoxy resin floor, the surface resistivity reaches 106 Ω - 109 Ω, and the ground resistance discharge meets the international gb6650-86a standard. The whole floor is seamless, which can achieve the following goals: dust-proof, tough and wear-resistant, impact resistant, heavy pressure resistant, corrosion-resistant, solvent resistant, flat and bright, color free, easy to clean, maintain and maintain, and long service life.
防静电地坪漆验收测量前，应用洁净的纱布将表面擦乾净，严重玷污的应用中性液清洗乾净，然后将室内空调打开，保持一定温度连续开上23天，规定的温湿度条件下测量。放置电极前先用软布条插去地表面所有尘物，电极表面在放置前要用乾净的软布条粘上异丙醇不少於70°´插试乾净，22面积，至少做5次测试。5次测试中最少3次的测试应当包括受磨损的有化学品或水溅落的有明显沾污的区域。
Before acceptance and measurement of anti-static floor paint, clean the surface with clean gauze, and clean the surface with neutral solution if it is seriously polluted, then turn on the indoor air conditioner, keep a certain temperature for 23 consecutive days, and measure under the specified temperature and humidity conditions. Before placing the electrode, insert a soft cloth strip to remove all dust on the ground surface. Before placing the electrode surface, use a clean soft cloth strip to stick Isopropanol at least 70 ° for insertion and test. The area of 22 should be tested at least 5 times. A minimum of 3 of the 5 tests shall include areas that are subject to wear and visible contamination with chemicals or water splashes.
避免在低温高湿条件下施工;双组份材料混郃后，应在短时间内施工;涂装完成后，应充分保养后，才能投入使用;应根据基材平整度状况和使用要求，确定涂层厚度。应采用越厚的涂装系统，涂层载重越大，涂层应越厚，如涂层过薄，使用过程中易损坏。 如一楼地面需做好防水处理。
Avoid construction under the condition of low temperature and high humidity; after two-component materials are mixed, construction shall be carried out in a short time; after coating, it shall be fully maintained before putting into use; the coating thickness shall be determined according to the flatness of the base material and the use requirements. The thicker the coating system, the heavier the coating load, the thicker the coating. If the coating is too thin, it is easy to be damaged in use If the ground of the first floor needs to be waterproof.
The anti-static floor paint is a two-component paint composed of high-grade epoxy resin, high-efficient conductive materials, high-grade pigment additives and a certain proportion of special curing agent for epoxy. The anti-static effect of epoxy anti-static floor paint is excellent and durable, moisture-proof, wear-resistant, and not affected by time, temperature, humidity, etc. The surface is smooth and smooth, which can eliminate and prevent the generation of static electricity and electromagnetic wave, and avoid the interference and damage of static sparks and electromagnetic wave.
防静电地板漆，漆膜表面电阻为106-109欧姆，优先防止静电荷泄露，消除静电积累和电磁乾扰的危害。环氧防静电地坪拥有环氧树脂地坪的一切优异性能，表面电阻率达到106Ω-109Ω、地面电阻排泄符郃国际GB6650-86A标准。该地板整体无缝，能达到:防尘、坚韧耐磨、耐冲击、耐重压、耐腐蚀、耐溶剂、平整亮丽、著色自由、便於清理、维护，保养，且使用寿命长之目的。
The surface resistance of anti-static floor paint is 106-109 ohm. The priority is to prevent the leakage of static charge and eliminate the hazards of static accumulation and electromagnetic interference. The epoxy anti-static floor has all the excellent properties of epoxy resin floor, the surface resistivity reaches 106 Ω - 109 Ω, and the ground resistance discharge meets the international gb6650-86a standard. The whole floor is seamless, which can achieve the following goals: dust-proof, tough and wear-resistant, impact resistant, heavy pressure resistant, corrosion-resistant, solvent resistant, flat and bright, color free, easy to clean, maintain and maintain, and long service life.
防静电地坪漆验收测量前，应用洁净的纱布将表面擦乾净，严重玷污的应用中性液清洗乾净，然后将室内空调打开，保持一定温度连续开上23天，规定的温湿度条件下测量。放置电极前先用软布条插去地表面所有尘物，电极表面在放置前要用乾净的软布条粘上异丙醇不少於70°´插试乾净，22面积，至少做5次测试。5次测试中最少3次的测试应当包括受磨损的有化学品或水溅落的有明显沾污的区域。
Before acceptance and measurement of anti-static floor paint, clean the surface with clean gauze, and clean the surface with neutral solution if it is seriously polluted, then turn on the indoor air conditioner, keep a certain temperature for 23 consecutive days, and measure under the specified temperature and humidity conditions. Before placing the electrode, insert a soft cloth strip to remove all dust on the ground surface. Before placing the electrode surface, use a clean soft cloth strip to stick Isopropanol at least 70 ° for insertion and test. The area of 22 should be tested at least 5 times. A minimum of 3 of the 5 tests shall include areas that are subject to wear and visible contamination with chemicals or water splashes.
避免在低温高湿条件下施工;双组份材料混郃后，应在短时间内施工;涂装完成后，应充分保养后，才能投入使用;应根据基材平整度状况和使用要求，确定涂层厚度。应采用越厚的涂装系统，涂层载重越大，涂层应越厚，如涂层过薄，使用过程中易损坏。 如一楼地面需做好防水处理。
Avoid construction under the condition of low temperature and high humidity; after two-component materials are mixed, construction shall be carried out in a short time; after coating, it shall be fully maintained before putting into use; the coating thickness shall be determined according to the flatness of the base material and the use requirements. The thicker the coating system, the heavier the coating load, the thicker the coating. If the coating is too thin, it is easy to be damaged in use If the ground of the first floor needs to be waterproof.
